Contact Us

We want to hear from you! 

If you have any questions regarding sales, have a product question and you can't find the answer in the FAQ area, feel free to drop us a message. We will aim to respond to you within 24 hours. 

         

123 Street Avenue, City Town, 99999

(123) 555-6789

email@address.com

 

You can set your address, phone number, email and site description in the settings tab.
Link to read me page with more information.

Driver issue..驅動程式問題..驱动程序问题

 

....Can other drawing tablet drivers co-exist with WoodPad driver in 1 same computer?..安裝 Woodpad 驅動程式後,還可使用其他繪圖平板裝置嗎?..安装Woodpad驱动程式后,还可以使用其他绘图平板装置吗?....

.... The WoodPad driver should be exists independently in the cmputer. Due to the device is driven by certain protocol, other drivers with same protocol can cause command conflict and malfunction can happens. .. 無法使用。 任何繪圖板的驅動程式同時安裝會有衝突造成使用錯誤的情況發生,請先移除其他繪圖平板裝置驅動程式,並且重啟電腦,再安裝WoodPad驅動程式再次重啟電腦。 .. 无法使用。 任何绘图板的驱动程序同时安装会有冲突造成使用错误的情况发生,请先移除其他绘图平板设备驱动器,并且重启电脑,再安装WoodPad驱动程序再次重启电脑。 ....

....Can WoodPad driver be used with devices from other brands?..安裝 Woodpad 驅動程式後,還可使用其他繪圖平板裝置嗎?..安装 Woodpad 驱动程序后,还可使用其他绘图平板装置吗?....

....The WoodPad driver can only detect and function with WoodPad, other devices may not be functioned correctly..不行, WoodPad驅動程式僅供 WoodPad作使用,其他繪圖平板無法使用本應用程式..不行, WoodPad驅動程式僅供 WoodPad作使用,其他繪圖平板無法使用本應用程式。....

....I plugged WoodPad into my computer, the mouse isn’t moving. ..我將 WoodPad 接到電腦後,滑鼠就無法作用。..我将WoodPad接到电脑后,滑鼠就无法作用。....

....Since WoodPad is a Plug-n-Play device, the computer needs a few second to register the devie to be functional. If it cannot be functional after 30 seconds, please replug to another USB port. If the mouse is still not moving with the pen, please try the same procedure with another computer. If nothing will help, please contact where you bought from or local support for an exchange. .. WoodPad 是一款隨插即用的繪圖板,接到電腦後,請靜候電腦將本裝置登錄為 USB 裝置,大多數的電腦都能很快處理完此程式。待電腦登錄本裝置後,請再試一次。如果電腦無法將 WoodPad 登錄為 USB 裝置,請接到另一個 USB 埠試試。如果滑鼠依然無法作用 請試著在其他電腦上使用本裝置。如果將 WoodPad 接到該裝置後還是無法作用,請聯絡客服人員要求更換。 .. WoodPad 是一款即插即用的绘图板,接到电脑后,请静候电脑将本装置登录为 USB 装置,大多数的电脑都能很快处理完此程序。待电脑登录本装置后,请再试一次。如果电脑无法将 WoodPad 登录为 USB 装置,请接到另一个 USB 埠试试。如果鼠标依然无法作用 请试着在其他电脑上使用本装置。如果将 WoodPad 接到该装置后还是无法作用,请联络客服人员要求更换。....

....Why does pen pressure work in Microsoft Office but not on my drawing applications? ..為什麼手寫筆壓在 Microsoft Office 上可以作用,但是在繪圖應用程式就不行?..为什么手写笔压在Microsoft Office上可以作用,但是在绘图应用程式就不行?....

....Please download and install our driver to activate the pen pressure in drawing software. .. 必須安裝驅動程式後,才能在繪圖應用程式上使用手寫筆壓功能。請下載上述的驅動程式。 .. 必须安装驱动程式后,才能在绘图应用程式上使用手写笔压功能。请下载上述的驱动程式。 ....

....Th driver cannot install properly..我的驅動程式無法下載..我的驱动程式无法下载....

....

  1. ....If the WoodPad driver failed to load properly, first perform the recommended action in any error message that may appear on your screen. If that does not solve the problem, review the troubleshooting procedures below. ..如果 WoodPad 驅動程式無法正確載入,請先執行螢幕中出現的任何錯誤訊息之建議動作。如果無法解決問題,請查看下列的疑難排解程序。..如果WoodPad驱动程序无法正确载入,请先执行萤幕中出现的任何错误讯息之建议动作。如果无法解决问题,请查看下列的疑难排解程序。....
  2. ....Look in the troubleshooting tables below. Your problem may be described there and you can try the solution offered. ..請查看 [疑難排解表]。您可以在此查看問題說明,並嘗試執行提供的解決方案。..请查看[疑难排解表]。您可以在此查看问题说明,并尝试执行提供的解决方案。....
  3. ....Test your tablet and input tools. See testing your tablet and testing your tools..請測試您的數位板和輸入工具,請參閱 [測試數位板和測試工具]。..請測試您的數位板和輸入工具,請參閱[測試數位板和測試工具]。....
  4. ....If you are having a compatibility conflict between WoodPad and a new hardware or software product, see obtaining driver downloads for information on downloading an updated software driver. WoodPad periodically updates the software driver to maintain compatibility with new products. ..如果 WoodPad 和新硬體/軟體產品不相容,請參閱[取得驅動程式下載],瞭解下載更新的軟體驅動程式相關資訊。WoodPad 會定期更新軟體驅動程式,以期能夠持續支援新產品。..如果需要更新软件驱动程序,请参阅[取得驱动程式下载],了解下载更新的软体驱动程式相关资讯.WoodPad会定期更新软体驱动程式,以期能够持续支援新产品。....
  5. ....Driver could not install on Win7(SP1) without .NET Framwork V4.0 : Please download it HERE and install it. ..如果沒有 .NET Framwork V4.0,無法在 Win7(SP1) 上安裝驅動程式,請在此處 下載並安裝。..如果没有.NET Framework V4.0,无法在Win7(SP1)上安装驱动程序,请在此处下载并安装。....
  6. ....If you have tried the suggestions above and still cannot resolve the problem, then fill out the contact form HERE. ..如果試過上述建議後問題依然存在,請填寫 此處的聯絡表。....

....+ Testing Your Tablet..+ 測試繪圖板..+ 测试绘图板....

....Checking the Tablet..檢查繪圖板..检查绘图板....

  1. ....Turn on your computer and wait until the system has fully loaded. ..開啟電腦並等候系統完全載入。..开启电脑并等候系统完全载入。....
  2. ....Check the tablet connection. The tablet must be properly connected and registered it as a USB device on your computer. Make sure the tablet USB cable is securely connected to the tablet and to an active USB port on your computer. WoodPad requires that you connect to a primary USB port (located directly on your computer) or to a powered USB hub. ..檢查數位板連接情形。本數位板必須妥善連接,並在電腦上登錄為 USB 裝置,請確認數位板的 USB 連接線穩固地連接在數位板與電腦上可用的 USB 連接埠。您必須將 WoodPad 連接到主要 USB 連接埠(在電腦上)或供電的 USB 集線器。..检查数位板连接情形。本数位板必须妥善连接,并在电脑上登录为USB装置,请确认数位板的USB连接线稳定地连接在数位板与电脑上可用的USB连接埠。您必须将WoodPad连接 到主要USB连接埠(在电脑上)或供电的USB集线器。..检查数位板连接情形。本数位板必须妥善连接,并在电脑上登录为USB装置,请确认数位板的USB连接线稳定地连接在数位板与电脑上可用的USB连接埠。您必须将WoodPad连接到主要的USB连接埠(在电脑上)或供电的USB集线器。....
  3. ....If your computer does not register the tablet, try another USB port. ..如果您的電腦無法登錄本數位板,請嘗試使用其他 USB 連接埠。..如果您的电脑无法登录本数位板,请尝试使用其他USB连接埠。....
  4. ....If it still does not register the tablet, plug it into another computer with an active USB port. ..如果依然無法登錄本數位板,請接到另一台電腦上可用的 USB 連接埠。..如果依然无法登录本数位板,请接到另一台电脑上可用的USB连接埠。....

....Note: For best results when troubleshooting no power to the tablet, plug the tablet directly into the system USB port located on your computer. Temporarily eliminate any external hubs in use until you determine that the system recognizes the tablet and that it is functional. When the tablet is working properly, it is usually okay to then move the tablet to a powered USB hub .. 注意:解決數位板無法供電的問題時,將數位板直接接到電腦上的系統 USB 連接埠可達到最佳效果。請先暫時消除任何使用中的外部集線器,直到確定系統登錄本數位板且可使用為止。數位板可正常使用後,通常就能將數位板移至供電的 USB 集線器。 .. 注意:解决数位板无法供电的问题时,将数位板直接接到电脑上的系统USB连接埠可达到最佳效果。请先暂时消除任何使用中的外部集线器,直到确定系统登录本数位板且可 使用为止。数位板可正常使用后,通常就能将数位板移到供电的USB集线器。 ....

....Checking the Grip Pen..檢查感壓手寫筆..检查感压手写笔....

  1. ....Move your pen across the tablet active area; your cursor should move in the corresponding direction on your monitor or display screen. ..在數位板工作區域上移動手寫筆,顯示器或顯示螢幕上的游標應該會以對應方向移動。..在数位板工作区域上移动手写笔,显示器或显示萤幕上的游标应该会以对应方向移动。....
  2. ....Press the pen tip against the surface of the tablet. The system will perform Click. ..在數位板表面上壓住筆尖,系統會執行「按一下」功能。..在数位板表面上压住笔尖,系统会执行「按一下」功能。....
  3. ....Next, without applying pressure to the pen tip, hold the pen tip within approximately 7 mm of the tablet. See if the cursor moves on the screen. ..接著在筆尖不施壓的情況下,將筆尖維持在數位板約 7 公釐的範圍內,查看螢幕上的游標是否移動。..接笔在笔尖不施压的情况下,将笔尖维持在数位板约7公厘的范围内,查看萤幕上的游标是否移动。.... .... If these tests pass, then your pen is fully functional. If these tests do not tests fail, you may have a defective input tool or tablet. Contact us HERE.

Note: After testing, use the WoodPad control panel to reconfigure your tablet and tools for any custom settings you may originally have been using. .. 如果測試成功,便可完全發揮手寫筆的功能。如果測試失敗,可能是輸入工具或數位板損壞。請聯絡我們HERE.

注意:測試完畢後,請使用WoodPad 繪圖板的控制面板重新設定您原先使用的各種數位板和工具自訂設定。 .. 如果测试成功,便可完全发挥手写笔的功能。如果测试失败,可能是输入工具或数位板损坏。请联络我们这里

注意:测试完毕后,请使用WoodPad绘图板的控制面板重新设定您原先使用的各种数位板和工具自订设定。 ....

....+ Testing Your Tools..測試工具..测试工具....

.... To test your tool, the WoodPad driver must be installed onto your computer. ..若要測試工具,必須在電腦上安裝 WoodPad 驅動程式。..若要测试工具,必须在电脑上安装WoodPad驱动程式。....

  1. ....Open the driver and click the ABOUT button. The ABOUT dialog box displays to show dynamic information about the tablet hardware and pointing devices. ..開啟驅動程式並按一下 [關於] 按鈕,顯示的 [關於] 對話方塊會說明數位板硬體和指標裝置的相關動態資訊。 ..1.开启驱动程序并按一下[关于]按钮,显示的[关于]对话方块会说明数位板硬体和指标装置的相关动态资讯。....
  2. Press the pen onto the tablet, the values on the "Pointing Device Info" should change. ..在數位板上按壓手寫筆,應可更改「指標裝置資訊」的各項值。 ..在数位板上按压手写笔,应可更改「指标装置资讯」的各项值。....

alt text

....+ Testing The Pen..測試手寫筆..测试手写笔....

....With the diagnostic window still open, .. 在診斷視窗依然開啟的情況下: .. 在诊断视窗依然开启的情况下: ....

  1. ....Move your tool along the tablet surface. The X and Y DATA values should change to reflect the tool position. ..沿著數位板表面移動手寫筆,X 和 Y DATA 值應會隨著手寫筆的位置改變。..沿着数位板表面移动手写笔,X和Y DATA值应随随着手写笔的位置改变。....
  2. ....Click on the tablet surface with the tool tip – the PRESSURE value should change (PRESSURE should change from approximately 0% with no pressure applied to approximately 100% when full pressure is applied.) ..用筆尖按一下數位板表面,「壓力」值應會改變(「壓力」應該會從未施壓時的 0% 變成全面施力時的 100%(均為約略值))。..用笔尖按一下数位板表面,「压力」值应会改变(「压力」应该会从未施压时的0%变成全面施力时的100%(均为约略值))。....

...._Make sure when you are testing the pen your cursor is on your main screen. If you are using two monitors, do not test on your external monitor, the values will not move. Move your cursor onto your main screen and test again. ..測試手寫筆時,請確認游標在主螢幕上。如果使用雙顯示器,請勿在外部顯示器上測試,否則各項值不會移動。請將游標移至主螢幕後,再試一次。....

.... +Where can I contact Customer Support?..+我需要保固支援..+我需要保固支持....

....USA: Please message www.facebook.com/woodpad/ or email service@thewoodpad.com..台灣: 請私訊粉絲專頁https://www.facebook.com/WoodPadTW/ 或email至service@thewoodpad.com.. 中国:请打专线 4008-988-588....

....When contacting customer support, please provide the following details (1) Serial number (2) Purchase Date (3) Which store or channel you purchased..請聯絡所在地區的客戶支援中心,聯絡時請提供下列詳細資訊:(1) 序號;(2) 購買日期;(3) 購買商店或通路。..请联络所在地区的客户支持中心,联络时请提供下列详细信息:(1) 序号;(2) 购买日期;(3) 购买商店或通路。....

English
繁體中文
簡體中文